PURPLL giveaway+ more



Moderator: multi_s

Re: PURPLL giveaway+ more

Postby multi_s » Wed Oct 06, 2021 3:48 pm

hotfat wrote:Is there a way to completely turn off LFO contribution to the MULTIPLY and/or DIVIDE blocks? I realize one can set RATE and DUTY cycle to minimum but that doesn't completely eliminate it. I don't see any way explicitly mentioned in the manual. I just got this thing so I'm probably missing something obvious ... Thanks for any help. -Tim


Tall Walls wrote:Maybe I'm misunderstanding you, but that's what the toggles next to the Multiply and Divide knobs do.


Yes as Tall Walls says, that is basically what the MPY and DIV switch do. From the manual:

"The MULTIPLY switch connects the multiplier setting to the LFO’s
output when in the up position. In the down position the LFO does
not affect the multiplier’s value."

It is the same for DIV switch.

So with the switch DOWN the MPY and DIV knob statically assign a value to the multiplier and divider based on their position. And this value is not modulated by the lfo.

With their respective switches up, the multiplier and divider value are modulated by the LFO. In this case the MPY and DIV knob positions control the depth of the modulation on their respective parameters.

If you have any other questions, or if that explanation is not clear, please feel free to post more here.
multi_s

User avatar
IAMILF
IAMILF
 
Posts: 2071
Joined: Mon Feb 15, 2010 9:00 pm

Re: PURPLL giveaway+ more

Postby hotfat » Wed Oct 06, 2021 4:15 pm

Whoops! Thanks for the responses. Truly a bonehead oversight on my part. Sorry.
Thanks again for making the cool pedals, Scott!
hotfat

interested
interested
 
Posts: 42
Joined: Fri Dec 22, 2017 1:47 am

Re: PURPLL giveaway+ more

Postby multi_s » Wed Oct 06, 2021 4:21 pm

Hi

it's no problem, it is not super clear from the interface itself that that is what the switch does. but now you know :)
multi_s

User avatar
IAMILF
IAMILF
 
Posts: 2071
Joined: Mon Feb 15, 2010 9:00 pm

Re: PURPLL giveaway+ more

Postby hotfat » Sat Oct 09, 2021 2:33 pm

After my previous question, I sure hope the following hasn't been covered somewhere else.
Regarding the DRONE switch in down/off position and TRIGGER switch set to up/buffer position - The buffer seems to be on the order of 10s or 100s of milliseconds in length. Fairly short anyway. Is that correct? I don't hear any change in content when adjusting the DRONE knob to either extreme. Any insight? I guess if the buffer is small and the input signal didn't change alot during buffer capture, there wouldn't be any "different" program material to choose from. Also, Scott made mention of "glitch pll hell easter egg mode, etc" in a previous post. Is it kosher to ask how to get there? Thanks again for your kindness ...
hotfat

interested
interested
 
Posts: 42
Joined: Fri Dec 22, 2017 1:47 am

Re: PURPLL giveaway+ more

Postby multi_s » Sat Oct 09, 2021 4:16 pm

yes if you want to have a more salient experience just do something like plucking a string while sliding your hand up the fretboard (making an ascending tone sweep). then when you trim the buffer length it will probabl ybe easier to hear what is happening. The buffer is short but it also only fills for the period that the level of the input signal breaks the gate. So it does not always record the maximum amount of length, it depends on what was played.

if you want to have a more strange experience you can open the backplate and switch dips 5 6 and 7 to on. then use the buffer (trigger up)

yes there are some sections in the table of contents of the manual that do not exist, they should not be listed.
multi_s

User avatar
IAMILF
IAMILF
 
Posts: 2071
Joined: Mon Feb 15, 2010 9:00 pm

Re: PURPLL giveaway+ more

Postby hotfat » Sat Oct 09, 2021 7:27 pm

Got it. Thanks again, Scott.
hotfat

interested
interested
 
Posts: 42
Joined: Fri Dec 22, 2017 1:47 am

Re: PURPLL giveaway+ more

Postby cosmicevan » Sun Oct 10, 2021 10:33 pm

:wha?:




:eek:






:snax:
•○• cosmically yours •○•
cosmicevan

User avatar
FAMOUS
FAMOUS
 
Posts: 1059
Joined: Tue Feb 12, 2019 9:18 pm
Location: at the edge of oscillation, NY

Previous

Return to Montreal Assembly



Who is online

Users browsing this forum: No registered users and 3 guests


Sponsored Ad. (Please no inflated/repetitive clicking. Thanks!)



ilovefuzz.com is not responsible for user-submitted content. Users participate at their own discretion and risk.