Page 46 of 159
Re: UG demos Catalinbread Belle Epoch Tape Delay with Everyt
Posted: Tue Jun 17, 2014 10:39 pm
by Chankgeez
In the manual, Catalinbread says it's fine up to 18V. They say it increases your tonal options.
Re: UG demos Catalinbread Belle Epoch Tape Delay with Everyt
Posted: Tue Jun 17, 2014 10:47 pm
by Uncle Grandfather
Chankgeez wrote:In the manual, Catalinbread says it's fine up to 18V. They say it increases your tonal options.
thanks, i just checked the online site too
saw a picture of the pedal and it says 9-18v on it.
also just got an email about paying for my maude
Re: UG demos Catalinbread Belle Epoch Tape Delay with Everyt
Posted: Tue Jun 17, 2014 10:52 pm
by Chankgeez
Re: UG demos Catalinbread Belle Epoch Tape Delay with Everyt
Posted: Wed Jun 18, 2014 1:05 am
by Uncle Grandfather
Hello, and thanks to reading instruction manuals I have a whole new appreciation of the Belle Epoch. First up was putting it in buffered mode, which sounds like a vastly improved version of the bypass mode, and also allows for trails after turning off the pedal. Next up was running at 18v instead of 9v which was a major improvement across the board.
Here with the MASF Raptio and a Jerms mkI.
[youtube]http://www.youtube.com/watch?v=UwOIF0_d7VA[/youtube]
Re: UG demos Catalinbread Belle Epoch Tape Delay with Everyt
Posted: Wed Jun 18, 2014 1:11 am
by Uncle Grandfather
Hi there, here is the Belle Epoch in buffered mode at 18v with a clari(not) with a creepy fingers fz-1.
[youtube]http://www.youtube.com/watch?v=yoITdS1ksDA[/youtube]
Re: UG demos Catalinbread Belle Epoch in buffered mode at 18
Posted: Fri Jun 20, 2014 1:45 pm
by Uncle Grandfather
Hello, here is the Dreadbox Sonic Bits Delay/Bitcrusher with a Korg SR-120
[youtube]http://www.youtube.com/watch?v=PvuCK7DhvZw[/youtube]
Re: UG demos Dreadbox Sonic Bits delay/bitcrusher
Posted: Sun Jun 22, 2014 12:13 am
by Uncle Grandfather
Hey, here is a look at the Industrialectric Squarewave Generator. Really cool fuzzy textures in this box.
[youtube]http://www.youtube.com/watch?v=fLF-5zRPokQ[/youtube]
Re: UG demos Industrialectric Squarewave Generator
Posted: Sun Jun 22, 2014 12:29 am
by Uncle Grandfather
Hey is a different look at the Squarewave Generator.
[youtube]http://www.youtube.com/watch?v=kqBcHluK9eY[/youtube]
Re: UG demos Industrialectric Squarewave Generator
Posted: Mon Jun 23, 2014 5:49 am
by Uncle Grandfather
Hiya, here is the Industrialectric Blackbox Overdrive and Squarewave Generator.
[youtube]http://www.youtube.com/watch?v=sQK6FBb8lok[/youtube]
Re: UG demos Industrialectric Tourbox
Posted: Mon Jun 23, 2014 4:57 pm
by Uncle Grandfather
Hey there, here is the awesome Blackbox Overdrive.
[youtube]http://www.youtube.com/watch?v=4FfM6YHaiNE[/youtube]
Re: UG demos Industrialectric Tourbox
Posted: Mon Jun 23, 2014 6:28 pm
by intothegroove
Re: UG demos Industrialectric Tourbox
Posted: Mon Jun 23, 2014 9:32 pm
by Uncle Grandfather
Hey there, here is the gotta get one of these Reverb Machine with the Incinerator, no input signal.
[youtube]http://www.youtube.com/watch?v=IB2wOMV4MrE[/youtube]
Re: UG demos Industrialectric Tourbox
Posted: Tue Jun 24, 2014 12:36 am
by Uncle Grandfather
Heylo, this is the seriously awesome Reverb Machine.
[youtube]http://www.youtube.com/watch?v=kCU2o1quGPM[/youtube]
Re: UG demos Industrialectric Tourbox
Posted: Tue Jun 24, 2014 8:29 am
by nevada
UG, what causes the flanging sort of sound in the beginning of that last Reverb Machine demo?
Re: UG demos Industrialectric Tourbox
Posted: Tue Jun 24, 2014 8:37 am
by MrNovember
The RM-1N sounds soo good. SO much gas!
