Page 2 of 2
Re: Pedal Rehousing! Should I go for it and who does it?
Posted: Fri Sep 07, 2018 12:00 pm
by Confuzzled
rfurtkamp wrote:It'll be worth your effort - the topography of the signal path is fascinatingly oddball.
Sample+hold you can adjust the time non-destructively and bring it back - and LFO is post-buffer as well, so you can make it do all sorts of warbling then back off and return.
It was my go-to destructobox live where I'd run it into a Bassman with 1x15 JBL, crank it up to ungodly, sel the LFO to deep and slow, turn down the time on a loop, and use it as a background pulsing ugly drone.
Yeah, I don't know what I'm in for once I get the power supply working. I would love to circuit bend it but I only mess with battery powered items to avoid shortening my lifespan. Also wanted to see if the chips came out and I could plug them into other boards.
Re: Pedal Rehousing! Should I go for it and who does it?
Posted: Fri Sep 07, 2018 2:47 pm
by whoismarykelly
Confuzzled wrote:rfurtkamp wrote:It'll be worth your effort - the topography of the signal path is fascinatingly oddball.
Sample+hold you can adjust the time non-destructively and bring it back - and LFO is post-buffer as well, so you can make it do all sorts of warbling then back off and return.
It was my go-to destructobox live where I'd run it into a Bassman with 1x15 JBL, crank it up to ungodly, sel the LFO to deep and slow, turn down the time on a loop, and use it as a background pulsing ugly drone.
Yeah, I don't know what I'm in for once I get the power supply working. I would love to circuit bend it but I only mess with battery powered items to avoid shortening my lifespan. Also wanted to see if the chips came out and I could plug them into other boards.
If it takes AC from the wall it almost assuredly has a small transformer inside that just converts that to a smaller DC voltage. Unless you tough the AC contacts directly you should be fine. Its still going to be a low-voltage device.
Re: Pedal Rehousing! Should I go for it and who does it?
Posted: Fri Sep 07, 2018 2:50 pm
by Confuzzled
whoismarykelly wrote:Confuzzled wrote:rfurtkamp wrote:It'll be worth your effort - the topography of the signal path is fascinatingly oddball.
Sample+hold you can adjust the time non-destructively and bring it back - and LFO is post-buffer as well, so you can make it do all sorts of warbling then back off and return.
It was my go-to destructobox live where I'd run it into a Bassman with 1x15 JBL, crank it up to ungodly, sel the LFO to deep and slow, turn down the time on a loop, and use it as a background pulsing ugly drone.
Yeah, I don't know what I'm in for once I get the power supply working. I would love to circuit bend it but I only mess with battery powered items to avoid shortening my lifespan. Also wanted to see if the chips came out and I could plug them into other boards.
If it takes AC from the wall it almost assuredly has a small transformer inside that just converts that to a smaller DC voltage. Unless you tough the AC contacts directly you should be fine. Its still going to be a low-voltage device.
Its a shame those boards are so big inside otherwise Id attempt putting it in a large enclosure and make it a stompbox
Re: Pedal Rehousing! Should I go for it and who does it?
Posted: Fri Sep 07, 2018 3:58 pm
by Confuzzled
Got a resource question: Best place to get 9 volt battery snaps. Bought some off of amazon and they were cheap crap. Any suggestions?
Re: Pedal Rehousing! Should I go for it and who does it?
Posted: Sat Sep 08, 2018 1:33 pm
by DannDubbleEwe
Re: Pedal Rehousing! Should I go for it and who does it?
Posted: Mon Sep 10, 2018 10:40 am
by Confuzzled
DannDubbleEwe wrote:http://www.smallbear-electronics.mybigcommerce.com/9-volt-battery-snap-hard-shell-t-style/
Thanks Dan! You are the man!!
Re: Pedal Rehousing! Update on ibanez knobs!
Posted: Thu Sep 13, 2018 2:11 pm
by Confuzzled
bump